JCase Posted March 10, 2016 Share Posted March 10, 2016 I have the Tunze 9001 installed in chamber 2 in my Coralife Biocube 29 When I do a feeding and the return pump turns off, which also turns off the skimmer. The collection cup from the skimmer floats up and off the skimmer since the water level increases because the return pump is off. Any suggestions to remedy this? Thanks, JCase Link to comment
StevieT Posted March 11, 2016 Share Posted March 11, 2016 Add a little bit of weight to the lid? A few spare magnets, put something heavy inside the cup. Rubble piece, dead hookers parts etc. Link to comment
StevieT Posted March 11, 2016 Share Posted March 11, 2016 When I do a feeding and the return pump turns off, which also turns off the skimmer. The collection cup from the skimmer floats up and off the skimmer since the water level increases because the return pump is off. Where do you run your water level at in chamber two? Link to comment
jamescstein Posted March 20, 2016 Share Posted March 20, 2016 I have the Tunze 9001 installed in chamber 2 in my Coralife Biocube 29 When I do a feeding and the return pump turns off, which also turns off the skimmer. The collection cup from the skimmer floats up and off the skimmer since the water level increases because the return pump is off. Any suggestions to remedy this? Thanks, JCase I've got 3 2" ceramic frag plugs sitting on top of mine. If I don't put them there and the cup is empty it will float when I turn the pump off. Link to comment
JCase Posted March 20, 2016 Share Posted March 20, 2016 Where do you run your water level at in chamber two?3.25 inchs down from the top lip of the back rim of the coralife biocube 29Which is also 3 inch below the divider between chamber 2 and 3 (Hope that makes sense, if not I'll take a picture of it) In chamber 3 the ato float maintains the level at 3.25 inches below the divider between chamber 2 and 3 Link to comment
JCase Posted March 20, 2016 Share Posted March 20, 2016 I find adjusting the height of the skimmer to the water level in chamber 2 to be a pita. I have an idea that I'm going to work on next week if I have time to make it very adjustable. I'll post pictures if it works out. Link to comment
JCase Posted March 22, 2016 Share Posted March 22, 2016 It seems I produce a lot more skuz overnight then I do during the day. My cup is full most mornings, but running all day very little is produced. Has anybody else observed this, or is it unique to my setup? Link to comment
reefhound Posted March 27, 2016 Share Posted March 27, 2016 9001 in a IM 25 Lagoon split the plastic on the magnet.. this will give you just enough room to glue it to the side of the skimmer and set the skimmer in the middle chamber... this is much, much easier than it looks. a hacksaw blade in hand cuts nicely, the gap lets it "self guide" the Y in the back will need to be re-split to allow room... I opted for 2 new pumps to run the lines straight up. these are adjustable flow, and worked out perfect. cut the 1/2" ID tubing to 6.25" lengths sand the plastic on the magnet smooth and glue it to the "long Side" done notice I added a little needle valve.. precise/easy adjusting also, don't worry about trying to cram the pumps off to the side or monkeyed around... set them down in straight, everything will have plenty of room.. adjust the flow you want on the pumps first.. that part is a pain later. note: I also did this to be able to put one of the pumps on a battery backup Link to comment
reefhound Posted March 27, 2016 Share Posted March 27, 2016 this morning I got up and made an "L" bracket that sits upside down under the skimmer to keep it from drifting around.. you can be a little more forceful with it and it keeps it at the height I want. anyone working with kydex? you can heat it with a micro torch and bend it to where you want it... it's what I make a lot of little mods. the .060 thickness is best for tank applications.. find it on fleabay Link to comment
Sujisuji Posted March 12, 2017 Share Posted March 12, 2017 In the manual it says Skimmer needs to be in a quiet low flow area? I want to put in my 17gallon cube in the display tank that has high flow and has an ATO. Will it not work properly since it's high flow? Link to comment
Recommended Posts
Archived
This topic is now archived and is closed to further replies.