spanko Posted December 30, 2010 Share Posted December 30, 2010 i pulled it out. not sure exactly what it means to reseat but pulled out impeller and just reinstalled it. and it still does it? Pull it apart again. Make sure that the little rubber knobs on the ends of the shaft are on all the way. Careful here don't break the shaft. The take a q-tip and make sure nothing is in the hole on the pump end where the shaft goes into. Then make sure that when you put the shaft in the motor body end it is all the way in. Careful here, don't break the shaft. Then reassemble the screw cap on the other end making sure it is good and tight. This is what was sent to me and worked: The impeller may not be seated correctly, all the way in. Have had this before on mine and took the impeller out, cleaned and then reseated it and all was good. Mine seems to get louder when it gets real dirty and goes back to being nice and quiet after cleaning. Yup, gotta clean mine about once per month. Quote Link to comment
cjrudy Posted December 30, 2010 Share Posted December 30, 2010 (edited) OK, mine has been in for a week and I have a few problems, first, because the skimmer is in chamber one, it kind of blocks the natural intake flow, and now i am getting a lot of crap floating on the top of the water instead of getting sucked into the top level of my media rack, and also the skimmer cup was collecting big chunks of crap. I still need steves media rack in chamber two to do its job, but it seems as if the skimmer is preventing that, or do I need a stronger pump than the stock pump. Edited December 31, 2010 by cjrudy Quote Link to comment
Derekcaudill Posted January 4, 2011 Share Posted January 4, 2011 Put mine in last night with Stevies media rack and everything is great so far. Really cant hear the skimmer at all. Nice clean install. Now I just sit back and wait for the skim!! Quote Link to comment
cberglof Posted January 5, 2011 Share Posted January 5, 2011 I have a 115 on order! Just wondering if anyone has the lower intake blocked with this install? Just getting my biocube 29 up, but have read some people block it for better surface skimming Also is it ok to put my heater in with cheto in chamber 2? I don't have it in a media basket. Quote Link to comment
Derekcaudill Posted January 5, 2011 Share Posted January 5, 2011 I have a 115 on order! Just wondering if anyone has the lower intake blocked with this install? Just getting my biocube 29 up, but have read some people block it for better surface skimming Also is it ok to put my heater in with cheto in chamber 2? I don't have it in a media basket. Mine is not blocked. I think with the skimmer in chamber 1 its better to not block it. Just my opinion. Quote Link to comment
chrisjj625 Posted January 10, 2011 Share Posted January 10, 2011 couple of questions what do you use to clean your cup its hard to get down on the sides of that cup? Also Mine went from producing nice brown stuff and went back to watery stuff should I clean it? This was only in for like 2-3 weeks. Quote Link to comment
Adzski Posted January 10, 2011 Share Posted January 10, 2011 (edited) hey well i dont have the same skimmer but when i clean my collection cup i just use really hot watter and detergent and pretty much just blast the cup with water but make sure u wash very throughly hope this helps? Edited January 10, 2011 by Adzski Quote Link to comment
Gr8_Outdoorsman Posted February 8, 2011 Share Posted February 8, 2011 Thank you very much for this detailed write-up. It was a huge help to say the least! One difference on my installation was the removal of the back plastic piece that the stock cartridge filter slides into. It wouldn't wiggle back and forth for an easy removal because the silicone or whatever they used to install it was way to strong. I pretty much had to pry and chip away the entire back plate piece by piece. It was a pain, but I got it! I'm still not completely comfortable with my heater being in chamber 3. The reason being is that if I shut the main pump off (to feed fish or basic maintenance) the water level quickly rises over the top of the heater as the levels in chamber 2 & 3 equalize with the rest of the tank. I'm using a 100W Fluval heater right now, but I don't have the water level up to the minimum level marking on the heater (about 1 1/2" below). Is this a major problem in your eyes and nothing to really worry about? Oh yeah, the AquaticLife skimmer is doing a bang up job. I already dumped 1/4" of pure yellow skim mate and I just put it in tonight. I can't believe that I even attempted to get the Biocube skimmer to work. It was pure junk, especially after seeing how well this one is performing. Quote Link to comment
teamguthix Posted March 24, 2011 Share Posted March 24, 2011 I take it the heater has to go inside the actual tank then since chamber 1 was the skimmer, 2 has the media baskets, and 3 the water level doesn't remain high enough? Quote Link to comment
pschom Posted March 24, 2011 Share Posted March 24, 2011 I have a 115 on order! Just wondering if anyone has the lower intake blocked with this install? Just getting my biocube 29 up, but have read some people block it for better surface skimming Also is it ok to put my heater in with cheto in chamber 2? I don't have it in a media basket. I have heater in 3rd chamber next to the pump. You shouldn't need to skim the surface if there's enough flow. Some people block the lower intake into chamber 1 for surface skimming. I have not done that but I heard it works. Quote Link to comment
LVReefer Posted March 26, 2011 Share Posted March 26, 2011 The micro bubbles are just part of the break in period. A vinegar bath can reduce the break in time along with opening up the return as much as possible. The skimmer usually takes 3 - 5 days to break in depending on the bio-load. It's a great little skimmer and with the money you save, invest it in a media basket. Quote Link to comment
Fluffeh Posted April 10, 2011 Share Posted April 10, 2011 what do you guys do for the heater? I have my heater in chamber one now, and with the mediabasket/fuge in chamber 2 there's no room in there... so chamber 3, but i dont have an ATO? what can i do? i want to get this skimmer but im worried about the heater. Quote Link to comment
russellh86 Posted April 16, 2011 Share Posted April 16, 2011 I use this heater in the 3rd chamber and it's working great. . . http://www.fosterandsmithaquatics.com/prod...fm?pcatid=20161 I do have an issue with my skimmer though. I installed it on my BC29 a couple of days ago using this great guide as a reference. Everything was working great, especially after I figured out that the air hose opening needed to be ABOVE the water line. However, yesterday I was making an adjustment to the flow rate and the knob just kept turning almost like it was stripped. What concerned me was as the knob turned, the flow rate wasn't changing at all. Has anyone ever had this issue before? Quote Link to comment
rO.oster Posted April 16, 2011 Share Posted April 16, 2011 (edited) the knob is just controlling a plastic ring that blocks the slanted grates on the right hand corner. lift the skimmer out of chamber 1, and see where the position lies in reference to where your spinning it. set it so all the grates are blocked, but if you rotate the knob (remember which way) you start to open it up. install it back to chamber 1, as high up as the back clip will let you go. turn it on, and slowly slowly rotate the knob to start raising the bubble level. the more open the grates are, the more air can circulate. I have my bubble level set to the bottom 25% of the riser cup, so that by the time foam pushes up and over, its the nasty stuff being skimmed out. dark green with chunks usually. tip: if you replaced that green tube that was from the stock tank, take it and clip off a 2 inch section, and install it over your knob as a extension handle. this will let you adjust the knob while its fully installed with just the fuge lid open. Edited April 16, 2011 by reeferRudy Quote Link to comment
Yves Posted June 4, 2011 Share Posted June 4, 2011 Has anyone used this skimmer with a MP-10? The reason I ask is because I've got the stock bio cube skimmer...was getting a decent amount of skimmate before adding the MP-10 now with the fluctuating water level in chamber 1 the foam never has enough time to rise high enough in the reaction chamber before it levels out again. Was wondering if the 115 is prone to the same problem that I'm experiencing. TIA Quote Link to comment
Fluffeh Posted June 4, 2011 Share Posted June 4, 2011 i have an mp10, how does the water level fluxuate in chamber 1? Quote Link to comment
EvoKnvl Posted June 4, 2011 Author Share Posted June 4, 2011 Has anyone used this skimmer with a MP-10? The reason I ask is because I've got the stock bio cube skimmer...was getting a decent amount of skimmate before adding the MP-10 now with the fluctuating water level in chamber 1 the foam never has enough time to rise high enough in the reaction chamber before it levels out again. Was wondering if the 115 is prone to the same problem that I'm experiencing. TIA I have a MP10 mounted on the left hand side and I don't have any water level fluctuations. The level should remain constant. Quote Link to comment
Yves Posted June 4, 2011 Share Posted June 4, 2011 In short pulse and reef crest modes the wave continues into chamber 1at least it does on mine, it fluctuates from 3/4 to an inch every second. With the skimmer cup off I can see the foam at the top of the skimmer rising and falling with the wave...in night mode, when it's calm in the tank the skimmer works. I've thought of building a baffle to keep the water around the skimmer at a constant level but with the 115 there would be no room to facilitate that mod...hopefully mine is just an isolated incident...frustrating none the less...mine is a bio cube 29 hqi, doubt the model matters but the the water level in chamber one is definatley following the patern of the wave. Also nice job with your build...and appologies for semi-hijacking the thread, it's not my intention. Quote Link to comment
Fluffeh Posted June 4, 2011 Share Posted June 4, 2011 my mp10 is on the right hand side and i never noticed any water fluxuations. where is your mp10 located? Quote Link to comment
Seakwon Posted August 24, 2011 Share Posted August 24, 2011 I bought this skimmer used and it didnt come with the clips. I put it in chamber 1 and filed down the edge of the stock biocube hood so that it would shut. well my problem is something that someone mentioned on here early in this post and that is because of the volume it take up in chamber 1 it has caused the water in the tank to go over the back lip into chamber 2 and three. is there some magic reason this is only happening to me, or is it because of the way that i put mine in? should I buy the plastic pieces or is it pretty much the same thing? Quote Link to comment
RedStang Posted October 25, 2011 Share Posted October 25, 2011 Thanks for the guide. Installed my skimmer Sunday. I've gone with suction cups only for the mounting. So far it's not pulling much but it's only been a couple of days. Where does everyone adjust the bubble level to? Quote Link to comment
pschom Posted October 25, 2011 Share Posted October 25, 2011 what do you guys do for the heater? I have my heater in chamber one now, and with the mediabasket/fuge in chamber 2 there's no room in there... so chamber 3, but i dont have an ATO? what can i do? i want to get this skimmer but im worried about the heater. As long as the water line in chamber 3 doesn't go below the heated part of the heater it should be fine. Just remember to check on it once every couple of days and top it off. Quote Link to comment
RyGuy103 Posted October 27, 2011 Share Posted October 27, 2011 I couldn't be more unimpressed with this skimmer. It makes the most aweful slurping/gurgling noise. I have tried several times to reset the impeller as many have suggested but this does not fix the problem. Back to the store it goes. Quote Link to comment
RyGuy103 Posted November 2, 2011 Share Posted November 2, 2011 I couldn't be more unimpressed with this skimmer. It makes the most aweful slurping/gurgling noise. I have tried several times to reset the impeller as many have suggested but this does not fix the problem. Back to the store it goes. I'm going to retract my last statement. I contacted AquaticLife about the problems I was having and they immediately send me a brand new skimmer and took back the old one at absolutely no cost to me. This is especially impressive given that I live in Canada and they paid shipping to and from LA. Thanks! Quote Link to comment
RedStang Posted November 2, 2011 Share Posted November 2, 2011 I'm going to retract my last statement. I contacted AquaticLife about the problems I was having and they immediately send me a brand new skimmer and took back the old one at absolutely no cost to me. This is especially impressive given that I live in Canada and they paid shipping to and from LA. Thanks! Excellent news and thanks for sharing! Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.