DaveFason Posted August 27, 2014 Share Posted August 27, 2014 Here is a great walk threw for building your own light stand. I personally LOVE the look of this. Credit goes to VicSkimmer from the forums. You can use scews to replace the grommets for hanging or run the steel cable into the conduit. "Left to right:SquareDremel (optional)Drill (with drill bits that can cut through steel)Conduit BenderEMT piping (not pictured, I used 1/2")Conduit Hangers (see figure 3)Conduit Clamp (see figure 3)Lowe's has literally everything you need for this project. They also sell 5' sections of 1/2" and 3/4" EMT pipe to make transporting it easier. If you plan on hanging the light much higher than 6" above the tank you'll likely need the longer pipe though. First of all you will need to learn to bend your EMT pipe. This is a good diagram of how to measure everything out, but I just did it by eyeing it. Make sure to buy multiple lengths of EMT pipe because you'll probably throw out quite a few while you're getting used to it You'll likely only need to bend it 90 degrees, and the bender has marks to help guide you (though not one for 90 degrees) I didn't take good pictures to show how to do this, but there are endless ways of bending the pipe to get the desired effect. You could just bend it once and connect the light stand to the middle of your aquarium stand and be done with it. I wanted to connect mine off to one side to make adjusting it easier, so I had to bend it twice. Essentially I had to bend it once to where I thought 90 degrees was and then use the square to make sure it was actually 90 degrees. You can fine tune it by bending it by hand. Just use your feet to pin it to the floor in a way you can get decent leverage. After it was bent once I had to do the second bend, and this is where I wasted the majority of my pipe. The easiest way I could do it was to mark off where my tank was going to be on the stand and try to imagine just how much pipe the 90 degree bend would take. Once you have both bends in it it's time to make sure both bends are square and exactly 90 degrees. This is where it gets a little tough to bend it by hand, because you don't want to tweak the first bend too much by adjusting the second one, so just take it slow. Next it's time to attach the pipe to the stand to make sure your contraption is tall enough to hang the light where you want it. These are the bits I used to hang mine. It's just 2 hanging brackets and a nice sturdy clamp that has a screw to help secure it at the bottom.Once you're sure it's going to be tall enough, use a tape measure to figure out exactly what height you think will be the maximum height you're going to want to hang the light. For me it was 6", so I had someone hold the pipe while I measured 23" from the top of the stand to the bottom of the pipe. I know my tank is 14" tall and the light is 3" tall, so to get 6" from the bulb to the top of the tank I needed 23". Make sure to factor in the height of the wire hanging kit if you're planning on using that instead of physically mounting the light to the light stand.Once you're sure that you have the correct height, mark that spot on the pipe right where the screw from the clamp will go. (measure twice, mark once). Use the drill (choose a drill bit large enough to allow the clamp screw to enter the EMT pipe) and drill a hole where you marked.If you're planning on using the wire hanging kit to adjust the height of your light, skip this next step.I didn't like being restricted to only one height, so I decided to alter the original design a bit. I marked the pipe in 1" increments in order to allow me to adjust the height, as seen below From there, you just need to drill holes in the top of the pipe where the mounting points on your light are. It's fairly straightforward, so I won't go into detail.Here I decided to clean up the original design some more. I didn't like the idea of having the power cord just hanging around, so I decided to drill a third hole in order to feed the power cord through it. This is where the dremel came in handy. I used one of these bits designed for cutting metal (but not for drilling holes) to widen the original hole I drilled until it was large enough to feed the power cable through it. The bit is also good for cleaning up the holes you've drilled, it can be used to smooth out rough edges, which is critical if you plan on feeding the power cable through it. Make sure to wear safety glasses and gloves as bits of metal will irritate your skin and you wouldn't want them to get in your eyes.From there you need to dismantle your light in order to remove the power cable. I didn't take pictures of this because all lights are likely different. Then you just feed the power cable through the bottom of the pipe and use a hook or small screwdriver to pull them through hole you just drilled. Reconnect the light and test to make sure it works.Now's a good time to test fit the light stand with the light attached to it to make sure it looks and sits the way you like. From there you can either be done with it, or you can take it a few steps further.Remove the light stand from the aquarium stand and remove the light fixture from it.I decided to drill holes about 90 degrees around the pipe from the first ones in order to allow me to swing the light out of the way for maintenance. Totally optional but it might be necessary if your light takes up the majority of the space above your tank.From there you can hit it with 3 or 4 coats of heat resistant spray paint from Lowe's, I used the Rustoleum brand with a satin finish. it's the paint that's meant for grills. This should help prevent the stand from rusting and it gives it a nice finished look. Then wipe it down really well because that paint tends to leave a lot of dust and reassemble it. You're done!The end effect: All in all it took me about 4 hours to complete and the materials themselves cost about $10. If you need to buy the tools, the bender runs about $35+ (depending on the size), a drill runs probably $30+ and a dremel is likely a $100+ purchase." Link to comment
xiaoxiy Posted August 27, 2014 Share Posted August 27, 2014 Now please teach me how to run/hide my nanobox cord through the conduit, and you will be my hero. Link to comment
Spiderguardnano Posted August 27, 2014 Share Posted August 27, 2014 how can we hang the tide if it comes with the gooseneck Link to comment
JR! Posted August 27, 2014 Share Posted August 27, 2014 Now please teach me how to run/hide my nanobox cord through the conduit, and you will be my hero. disconnect the wires from the controller or driver. drill hole in the pipe. run wires down the pipe. connect the wires to driver or controller. done. Link to comment
RollaJase Posted August 27, 2014 Share Posted August 27, 2014 Really good guide Dave, personally this is my favourite light hanging method. Link to comment
xiaoxiy Posted August 27, 2014 Share Posted August 27, 2014 disconnect the wires from the controller or driver. drill hole in the pipe. run wires down the pipe. connect the wires to driver or controller. done. I was actually contemplating whether I should redo my light bar, paint it a powdered white and maybe do this. Dave, any advice? Link to comment
JR! Posted August 27, 2014 Share Posted August 27, 2014 I was actually contemplating whether I should redo my light bar, paint it a powdered white and maybe do this. Dave, any advice? id do that asap Link to comment
DaveFason Posted August 27, 2014 Author Share Posted August 27, 2014 Shoot me an email and I will send a how to. I am finally working on videos! Link to comment
Legendary Corals Posted August 27, 2014 Share Posted August 27, 2014 Shoot me an email and I will send a how to. I am finally working on videos! Would love to see vids Dave! Link to comment
Archaic37 Posted August 27, 2014 Share Posted August 27, 2014 Where did you find those clamps for the holes? Link to comment
DaveFason Posted August 27, 2014 Author Share Posted August 27, 2014 Everything is available at Lowes and HD. -Dave Link to comment
Chungy Posted August 28, 2014 Share Posted August 28, 2014 For a Nano box Quad, is 1/2 emt pipe strong enough? Link to comment
Mirya Posted September 1, 2014 Share Posted September 1, 2014 For a Nano box Quad, is 1/2 emt pipe strong enough? Yup, that is exactly what I used for mine: Link to comment
Smithjm5 Posted January 30, 2015 Share Posted January 30, 2015 Do you know what this is called Dave? I went to lowes and home depot and cant find it anywhere! Link to comment
DaveFason Posted February 2, 2015 Author Share Posted February 2, 2015 I will contact Jason on this. Give me a day. -Dave Do you know what this is called Dave? I went to lowes and home depot and cant find it anywhere! Link to comment
jbb Posted May 5, 2015 Share Posted May 5, 2015 Do you know what this is called Dave? I went to lowes and home depot and cant find it anywhere! http://m.lowes.com/pd/Gampak-12-in-Rigid-Clamp/1002121 I will contact Jason on this. Give me a day. -Dave Link to comment
Recommended Posts
Archived
This topic is now archived and is closed to further replies.