waldoz Posted May 9, 2021 Author Share Posted May 9, 2021 Been messing around with some rock scape ideas. Finding it hard to come up with something for a square cube. 🤪 It's just little over half at 14" and leaves room to grow up the rest of the tank. Not sure might have mess around some more. Quote Link to comment
waldoz Posted May 30, 2021 Author Share Posted May 30, 2021 Finally got it glued together. I did a video of the scape so you can see the depth. There is about 11 1/4" to the top top of the tank from the tip of the rock. Taking an inch or so for water level gives me about 10". So should be plenty of room for hammer's or frog spawn. Still trying to come up with some ideas for the sps we have and where to put that. I think we will fill in the gaps and do some cement work or more super glue. Seems to be holding pretty well though. We used the BRS large tube with the spray works pretty good. Would buy it again if I am ordering something. 1 Quote Link to comment
spectra Posted May 30, 2021 Share Posted May 30, 2021 Looks nice.............. what glue did you use ? I really like the emarco cement it works really well........... Quote Link to comment
waldoz Posted May 30, 2021 Author Share Posted May 30, 2021 BRS super glue. I only used it in few spots and it's doing good but I want to follow up with something more permanent. I will have to look at that stuff you suggested. I don't want to buy a ton as l don't think I need that much to finish it up. Looked at jb- wet and some hydrologic cement too. I'm open to some inexpensive options.😁 Quote Link to comment
spectra Posted May 31, 2021 Share Posted May 31, 2021 1 hour ago, waldoz said: BRS super glue. I only used it in few spots and it's doing good but I want to follow up with something more permanent. I will have to look at that stuff you suggested. I don't want to buy a ton as l don't think I need that much to finish it up. Looked at jb- wet and some hydrologic cement too. I'm open to some inexpensive options.😁 the JB stuff is the cheapest option.............. I use it at times and its reef safe. Quote Link to comment
waldoz Posted May 31, 2021 Author Share Posted May 31, 2021 The epoxy or the putty? I've used the two part epoxy would like the option to put sand on it if possible. Quote Link to comment
spectra Posted May 31, 2021 Share Posted May 31, 2021 The putty works well............thats all I have tried. Quote Link to comment
waldoz Posted June 13, 2021 Author Share Posted June 13, 2021 So ended up with JB water weld. So if I was to do it again I would have got 4 or five sticks. Total for 3 was $13 shipped to my door from Amazon. We will not see the backside, but it's not going anywhere. Also filled in the gap with smaller rubble. One other thing lightly have your fingers wet when mixing and application. It's easier and a lot cleaner. Still trying to figure out where to put the heaters. I think so far going to go with two 150w Jagers in the over flow with an Inkbird. If anyone has any other suggestions post up. Going to focus on the plumbing now and need to order some bulkheads and a gate valve. Not sure on pipe size yet. Thinking 1" out from the pump. I am trying to figure out a way to make water changes easy. Open for suggestions on the inexpensive side. Maybe something with the plumbing going in. All for now. 2 Quote Link to comment
waldoz Posted June 22, 2021 Author Share Posted June 22, 2021 Trying to find a tub to start the rock up and cycling. Ordered a bulk head and then thinking of putting a drain valve on the main drain. Pull the drain and empty the overflow into a bucket. Thinking 3 way valve. All for now. Quote Link to comment
waldoz Posted September 5, 2021 Author Share Posted September 5, 2021 Been busy with other projects. The Maxspec Razor is up for sale, just like the AI Hydra lights too much. Still coming back to drilling the back wall for return like @spectra suggested. The 20 L is filling up need to get moving on this. 1 Quote Link to comment
spectra Posted September 5, 2021 Share Posted September 5, 2021 I have bits somewhere if needed................... Quote Link to comment
waldoz Posted September 6, 2021 Author Share Posted September 6, 2021 Might have to take you up on that.😁 1 Quote Link to comment
waldoz Posted September 7, 2021 Author Share Posted September 7, 2021 Finally got a tub for the rock. Going to fill it up seed it with two Marine pure bioballs and some old tank change out water. With out going all out it should be fine with heater and power head. Thinking about six weeks or so. Am I on the right track? Quote Link to comment
waldoz Posted September 13, 2021 Author Share Posted September 13, 2021 Saltwater mixed and rock in @84deg. We don't want to take any thing from our current tank as we want fresh start. Looking for some ideas to seed the rock. Quote Link to comment
waldoz Posted September 14, 2021 Author Share Posted September 14, 2021 Too late son was changing out the water on the 20l and dumped a gollon of tank water in the bucket. He says it smells bad already. Going to let it stew for couple weeks at 83F and check it. Need to get moving and I am picking up an older mp10 for $30. If it works out try and find another used one. Quote Link to comment
spectra Posted September 14, 2021 Share Posted September 14, 2021 I cycled my pukani in the garage for about 3 months............. swapped out old tank water and also ran a cheap skimmer in the brute can it was in.............. oh also added some bio spera or something like that in there..,..... was cheap at petco.......... Quote Link to comment
righttirefire Posted September 15, 2021 Share Posted September 15, 2021 20 hours ago, waldoz said: Too late son was changing out the water on the 20l and dumped a gollon of tank water in the bucket. He says it smells bad already. Going to let it stew for couple weeks at 83F and check it. Need to get moving and I am picking up an older mp10 for $30. If it works out try and find another used one. Don't forget about your buddy that has aquarium parts and no running tanks. Water change station, nanobox leds, mp10s... 1 Quote Link to comment
spectra Posted September 15, 2021 Share Posted September 15, 2021 4 minutes ago, righttirefire said: Don't forget about your buddy that has aquarium parts and no running tanks. Water change station, nanobox leds, mp10s... No one wants your shit remember................... you need a tank just keep it............... Quote Link to comment
waldoz Posted September 15, 2021 Author Share Posted September 15, 2021 5 hours ago, righttirefire said: Don't forget about your buddy that has aquarium parts and no running tanks. Water change station, nanobox leds, mp10s... Got a mp10 for $30? LoL. I also have a Razor that no one seems to want. I think it might be out dated. I also suggest a 10 cube or a 2 gallon jar. Quote Link to comment
waldoz Posted September 20, 2021 Author Share Posted September 20, 2021 So the cube plumbing is done. It's very finicky though and if the flow is not perfect it starts pumping the overflow. I got it adjusted but I think I might have it setup wrong. 60 cube running. If the water level drops at all it starts making lots of noise if the level drops below the top of the piping. Overflow level When I turn off the pump to feed mode it doesn't overflow so that's good. I think I just have to make sure the skimmer is off. That's about it kinda wondering if I should change anything. Do you guys have any suggestions? Kids will be kids.🙄 Lego scuba diver and fishing boat. Here is the toilet flush. This happens when the valve on the drain is all the way open. Toilet flush! 1 Quote Link to comment
waldoz Posted September 21, 2021 Author Share Posted September 21, 2021 So for the heating was going to go with two 150w Jager with a Runco but now second guessing myself. Would two 125w Jager be better? Sump is about 9- 10 gallons so total 70 gallons not including rock etc. Suggestions? Quote Link to comment
waldoz Posted September 25, 2021 Author Share Posted September 25, 2021 Welp did some painting on the sump and used Krylon fusion gloss white. This stuff is great! Bottom Back side. And the finished sump. Also started painting the tank, silicone gave me some problems might need another coat. Don't want to see the overflow, because if the water is low you will definitely hear it. Still have not ordered the heaters and sand. Quote Link to comment
waldoz Posted September 25, 2021 Author Share Posted September 25, 2021 Yeah had to redo the white, I guess it turned out ok. . Painted the back black. So did not want the clear silicone standing out on the back drop. I had some black left so I tapped it and went over it. Next up is to paint the stand. The rock is cycling probably throw some jump start in the tub. 3 Quote Link to comment
waldoz Posted September 29, 2021 Author Share Posted September 29, 2021 Stuff is showing up 😁 Rancho temp controller and two Jager 125w heaters. Going to wire it up in next few days and put it on our 20L. 1 Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.