Jump to content
Littlest Reef

3g Fluval --> 30L Nuvo

Recommended Posts

mitten_reef
14 minutes ago, Littlest Reef said:

On the Tunze 9004 skimmer, I want to run it in the center chamber. With the Y split from the single pump, it doesn't fit. Has anyone run this with 2 mighty jets, presumably building some redundancy in and making room for the skimmer?

since 9004 has a top intake, your water level should be really steady to put in the center chamber (tight ATO tolerance, maybe optical vs float switch).  Otherwise, it'd also draw air thru that intake as well, iirc.  

 

I ran mine briefly in the second chamber (either side are the same size), and it fits perfectly. So one side can be heater, and the other skimmer.  just my take on it. 

Share this post


Link to post
Littlest Reef

@mitten_reef thanks, do you have the 9004? It doesn't seem to fit in 2/4. I was planning on using the Tunze 3155 for ATO. I did read some posts here that center chamber could be an issue with water level fluctuation, but if I run it in the outer intake chambers I dont think I'll get a good skim. 

 

I have some time here because if I can get water in it by this weekend I am not going to turn the skimmer on for a bit anyway as I am using Dr. Tims to cycle. Just waiting on some jurassic gel to do the scape. 

Share this post


Link to post
mitten_reef
11 minutes ago, Littlest Reef said:

@mitten_reef thanks, do you have the 9004? It doesn't seem to fit in 2/4. I was planning on using the Tunze 3155 for ATO. I did read some posts here that center chamber could be an issue with water level fluctuation, but if I run it in the outer intake chambers I dont think I'll get a good skim. 

 

I have some time here because if I can get water in it by this weekend I am not going to turn the skimmer on for a bit anyway as I am using Dr. Tims to cycle. Just waiting on some jurassic gel to do the scape. 

yup, that's the one I have, not the DC one tho, doubt if that make any difference.  the intake has to face chamber 1, and have the "outside" magnets out in the center chamber, I think.  their magnets are all the same, so shouldn't matter if you have them under water.  if you don't run a full-height media basket, then you might be able to keep the "outside" magnet in chamber 1 and intake face opposite.  I hope that makes sense. 

Share this post


Link to post
Littlest Reef

That is strange, maybe the models changed? The dimensions on the 9004 I have are 4.3L x 3.5W. Per the 30l manual, chambers 2 and 4 are 3.9" W and L. It does fit in 1/5, but not 2/4. Dimensionally I am excluding the magnets. 

Share this post


Link to post
mitten_reef
54 minutes ago, Littlest Reef said:

That is strange, maybe the models changed? The dimensions on the 9004 I have are 4.3L x 3.5W. Per the 30l manual, chambers 2 and 4 are 3.9" W and L. It does fit in 1/5, but not 2/4. Dimensionally I am excluding the magnets. 

many apologies....just went downstairs to try to mock the skimmer....I have terrible memory!  it def won't fit there.  Sorry for the confusion!

 

maybe that's why I was more concerned about water level in the center return chamber.  😅

Share this post


Link to post
Littlest Reef

Yes, I think I am going to grab a 2nd mightyjet and undo the Y connection. I may not even need the 2nd gyre. Btw the packaging and general presentation of the RW 25 is awesome. 

 

Hopefully water in and cycling by this weekend. 

  • Like 1

Share this post


Link to post
jcreefer

You can certainly run two pumps for redundancy.  Alternatively, you can just as easily replace the tubings and have one longer, one shorter and thereby pushing a single pump a bit more to one side of the center chamber.  
 

looks like a great start!  Be sure to keep us updated.  I’m really interested in the review of the ReefWave.

 

Jeff

Share this post


Link to post
Littlest Reef

I began messing with the rock tonight. I have a lot of reef saver foundation and shelf rock. The shelf is doing it for me. Jurassic gel drying thanks to 4 lbs of Kalk holding things together.

 

 

4936D51D-6826-416C-98F4-39CF94C88B5C.jpeg

  • Like 1

Share this post


Link to post
Littlest Reef

Well I jinxed the 3 gallon. Was just discussing with my wife that we’ll have to consider what to do with our azure damsel when the 30 is set up, because it will likely harass whatever else goes in except maybe clowns. After an afternoon at the beach we got home and “glowey” had jumped out, and unfortunately my 4 year old was the one time find him. That was a rough way to learn about life and death for the first time. This morning she was pretty much over it and is now hell bent on a purple dottyback. 

Share this post


Link to post
Littlest Reef

Tank has water. Excuse the wire, the gap to run them to the cabinet is small enough that I had to wire the skimmer before installing it, so it is sitting off screen. 
 

 

C234C6F0-EE3B-4BD9-A959-9FC52562CA58.jpeg

014D50DF-3EEB-48D9-9CFB-077AD71A2AC7.jpeg

DBEDC2F5-F986-43B0-8F41-63BB61334CDF.jpeg

Share this post


Link to post
hinnenkm

Looks good!

Share this post


Link to post
Littlest Reef

Big fan of Jurassic gel and the shelf rock. By spritzing RO water on the joints was able to get an extremely hard bond. The main piece is a ledge overhand that looks like a pile of rocks but is not actually connected so I can move them apart if need be.

9B84325A-51C2-4C7E-B193-69D3CAC1D3CA.jpeg

  • Like 1

Share this post


Link to post
Littlest Reef

Update on these tanks:

 

3 gallon has had a pod explosion Since the damsel died. I am still thinking through what to do with this tank, but it may make sense to go zoa garden only and keep it as a pod source for the 30 gallon. Also, tiny snail has emerged I think might be a baby spiny astrae? Also, Duncan coral may have been stung by the octospawn which I have relocated. Looking like a half deflated balloon.

 

Mighty jet and ATO arrive for the 30 today. Tank has settled out but even at 20% power the reef wave is creating the swale in the front of the tank which may be a problem until I get a second gyre.  Seeing if spin streams on the returns fixes it.

D7F8334F-EEC6-4651-8F38-C05927EE1F57.jpeg

91EA1336-E6C2-41FE-B760-3F093412688C.jpeg

0FA6D0DC-D6C7-4E69-80AD-6BDDC262D997.jpeg

Share this post


Link to post

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recommended Discussions

×
×
  • Create New...