junginit Posted May 23, 2011 Share Posted May 23, 2011 Thanks for the info! Good to keep in mind! Quote Link to comment
Pjanssen Posted May 23, 2011 Share Posted May 23, 2011 Beautiful! A local store suggested adding a stress syme or bio spiria when changing water. You didn't mention it. I just did a 20% water change and added the stress syme and actually ended up with higher nitrates than before I changed. Could the stres syme be the culprit. Quote Link to comment
StevieT Posted May 24, 2011 Author Share Posted May 24, 2011 Don't use any of that junk. If you are using RO water there is no point to start with. Junky freshwater products and bad advice IMO just to make a sale. Nitrates can come from you stirring up junk during the water change. Quote Link to comment
Pjanssen Posted May 24, 2011 Share Posted May 24, 2011 Don't use any of that junk. If you are using RO water there is no point to start with. Junky freshwater products and bad advice IMO just to make a sale. Nitrates can come from you stirring up junk during the water change. Okay. Thanks Quote Link to comment
brandon429 Posted May 25, 2011 Share Posted May 25, 2011 well written stuff so far, agreed I would never use bacterial supplements for water changes the bacteria are set in balance naturally and don't go away unless you use antibacterial products. they never need boosting during the life of the tank after they are established. No normal mistake you could make would kill them either> salinity issues won't kill them, pH issues won't kill them, they are the last thing to die in any reef tank. google this: "nitrate in the reef aquarium by randy holmes farley" its the best nitrate workup Ive ever seen. Quote Link to comment
junginit Posted May 26, 2011 Share Posted May 26, 2011 Thanks for the tips...I didn't think about the extra heater to pre-heat the water. Good thing I read this post. Quote Link to comment
bjbass Posted September 1, 2011 Share Posted September 1, 2011 How do you know how much salt to put it in? I am going be needing to fill my BioCube 14 and I am going to use 5 gallon buckets of RO water. How much salt would I need in a 5 gallon bucket full of water? Quote Link to comment
clownfish14 Posted September 1, 2011 Share Posted September 1, 2011 Depends on the salt. For the first time you kinda guess and mrasure with a refractometer. Then once you figure out about how much you need its easy. Quote Link to comment
1fishmonger Posted September 1, 2011 Share Posted September 1, 2011 I wonder how much money StevieT made off making this guide... #badmrcoral BTW - You should make one for how to get rid of cyano That's where the big money is. LOL Great job st Quote Link to comment
seanathen Posted September 1, 2011 Share Posted September 1, 2011 Most of the salt packages will tell you how much salt to add and come with a measuring cup. That's usually a good starting point. It always seems like I have to add a little more though... Quote Link to comment
Rocket Posted September 1, 2011 Share Posted September 1, 2011 The standard measuring of salt is 1/2 cup per gallon of water. Start with that. Quote Link to comment
bjbass Posted September 2, 2011 Share Posted September 2, 2011 (edited) The standard measuring of salt is 1/2 cup per gallon of water. Start with that. Ok, great! Thanks! I am using the same salt as Stevie-T. Red Sea Coral Pro Salt. It comes in the mail today. Does anybody have any experience with this brand and how much a gallon of RO would need? Somebody mentioned it depends on the brand. Edited September 2, 2011 by bjbass Quote Link to comment
JR! Posted September 27, 2011 Share Posted September 27, 2011 awesome walk through Quote Link to comment
Nanny Posted October 1, 2011 Share Posted October 1, 2011 From a new bee stand point this guide rocks! Thanks for taking the time to write it up!!! Quote Link to comment
Lokko21 Posted December 8, 2011 Share Posted December 8, 2011 Awesome guide, it help me a lot. THANKS. Quote Link to comment
dubmaneh Posted January 25, 2012 Share Posted January 25, 2012 Thanks for the great guide!! One question though, can I store salt water that I have already made in a new "jerry can" bought at a local hardware store? Quote Link to comment
StevieT Posted January 25, 2012 Author Share Posted January 25, 2012 You can, but what do you mean by jerry can? Like a bucket? If so yes, just keep it covered to avoid evaporation and always test it's salinity and heat it up with circulation before use. Quote Link to comment
dubmaneh Posted January 25, 2012 Share Posted January 25, 2012 You can, but what do you mean by jerry can? Like a bucket? If so yes, just keep it covered to avoid evaporation and always test it's salinity and heat it up with circulation before use. A red plastic gas can. It is new and never used for gas, but it is not food grade. Will it leach toxins into the water? I will definately test paramaters and make sure it matches the tanks water before using. I only plan on keeping enough for 1 or two water changes on hand, so it would be kept for a week or two. Quote Link to comment
StevieT Posted January 25, 2012 Author Share Posted January 25, 2012 Can't answer if it is safe or not, don't know if they line those with any coating. Would be easier just to make it in a bucket. I know it's easier to pour out of a can but you can't put a pump in it, you probably can fit the heater. Quote Link to comment
drewbold Posted February 1, 2012 Share Posted February 1, 2012 I just hook a tube to my water mixing pump and pump my new water into my tank so I dont have to worry about dumping in any until its down to like the last 1/4 inch of water. Was wondering though, my nitrates are high and I want to do a 15g water change from my 29bc, so I need a larger container for my water because I only have 2 xtra pumps and 1 xtra heater. So my 5gal bucket isn't going to do the trick. Any cheap suggestions I could run out to pick up? Quote Link to comment
StevieT Posted February 1, 2012 Author Share Posted February 1, 2012 Rubbermade type container. storage area of a hardware store. I use something similar for my ATO reservoir Quote Link to comment
drewbold Posted February 1, 2012 Share Posted February 1, 2012 oh ya great idea, I think I actually have some big ones in my storage room from when I moved, things are huge though, probably 40-50gal but that should work as long as I rinse it with RO first right? Or should I just be safe and go buy a new one. Thanks for the quick reply. ~Andy Quote Link to comment
StevieT Posted February 1, 2012 Author Share Posted February 1, 2012 You make the call but if they were for dry storage just rinse them out. I've moved my tank twice and both times I just go get a garbage can to make all the new water up in a head of time Quote Link to comment
trong Posted March 22, 2012 Share Posted March 22, 2012 Hello, I am new to this and I am in a cycle right now so I have yet to change the water. I was wondering do i really need a siphon or can i just scoop water out with a big jug or pitcher? is the a reason for the siphon? Quote Link to comment
Chrisl1976 Posted March 22, 2012 Share Posted March 22, 2012 Hello, I am new to this and I am in a cycle right now so I have yet to change the water. I was wondering do i really need a siphon or can i just scoop water out with a big jug or pitcher? is the a reason for the siphon? Just the way I do it..... I went a got two plastic food storage bins from Walmart. 6 gallons each. I mix up my water 3-4 gallons the night before. Check to make sure salinity, PH, and temp of the mixed water all match the tank. Set the empty bin next to the full bin next to the empty one and use a pitcher (cut the top off a 1 liter water bottom) to fill it up to the same amount. Then dump the new water in through the sump on the back of the tank. Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.